RAL1030 Roofing Pre Painted Steel Sheet DX51D 700mm 1250mm

RAL1030 Roofing Pre Painted Steel Sheet DX51D 700mm 1250mm

1. Product Overview

Pre painted roofing steel sheet is used where a metallic coated steel substrate and a finished color surface are both required in one material. This product range is suitable for roofing sheets, wall cladding, façade panels, and general building sheet fabrication where appearance, corrosion resistance, and forming compatibility need to be considered together.

The listed range covers 0.2–1.0mm thickness and 700–1250mm width. CGCC and DX51D are commonly used for painted construction sheet processing, while galvanized and galvalume base plate options allow the sheet to be selected according to service environment and project requirement.

2. Technical Solution

The product uses a coated steel base with an organic paint system on the exposed surface. In practical use, service performance depends on the combined effect of metallic coating level, paint film build, forming route, cut edge condition, and installation environment.

The metallic coating options on this page are Z60–Z275 for galvanized base and AZ30–AZ150 for galvalume base. The paint system uses 25±5 microns on the top side and 7±2 microns on the back side. This coating build is suitable for roofing and cladding fabrication where outdoor exposure, transport handling, and roll forming all need to be considered together.

The product is also listed as soft commercial quality or lock forming quality. That matters in actual processing because bend radius, profile depth, and forming stability depend on base material condition as well as paint system.

3. Specifications

4. Application

• This material is suitable for roof panels, wall cladding, façade sheets, and general exterior building panels.
• It can also be used for workshop roofs, warehouse panels, airport and storeroom cladding, vehicle related exterior sheets, furniture sheet parts, and electrical equipment housings where a finished painted surface is preferred over post-paint processing.
• For exterior applications, the final result depends not only on the coating system but also on panel profile design, overlap detailing, drainage condition, and the actual exposure environment.

5. Processing

• The sheet can be supplied for direct cut sheet use or for downstream profiling and forming.
• It is suitable for roll forming, bending, shearing, cutting, slitting, and general sheet metal fabrication.
• For deeper profiles or tighter bends, lock forming quality is usually more suitable than general commercial quality.
• Surface handling should be controlled during storage, cutting, and installation to reduce scratching on visible faces. Protective film can be used when the finished surface needs additional handling protection.

6. Advantages

• The 0.2–1.0mm range covers common roofing and wall panel sheet processing.
• The 700–1250mm width range matches mainstream panel and cladding production routes.
• Both galvanized and galvalume base options are available, which helps match different corrosion protection targets.
• The defined top and back paint thickness provides a clearer coating structure for fabrication and service selection.
• Multiple paint systems allow the sheet to be matched to standard use, better weather exposure, or higher finish retention requirements.
• RAL color customization supports project-based appearance matching.

7. How to Choose

• Choose galvanized base when the project requires a standard zinc coated painted sheet.
• Choose galvalume base when better exterior corrosion performance is required.
• Choose polyester for standard applications, SMP for improved weather resistance, and PVDF when long-term exterior appearance and UV resistance are more important.
• Choose lower thickness when easier forming and lighter panel weight are important. Choose higher thickness within the listed range when the panel needs more rigidity.
• Choose lock forming quality when the sheet will be used for deeper profiles or more demanding forming routes.

8. FAQ

Q1. What thickness range is available for this roofing steel sheet
The listed thickness range is 0.2–1.0mm.

Q2. What width range is available
The listed width range is 700–1250mm.

Q3. What metallic coating options are available
The listed metallic coating options are Z60–Z275 and AZ30–AZ150.

Q4. What paint systems are available
The listed paint types are polyester, SMP, and PVDF.

Q5. Can this product be used for roofing and wall cladding
Yes. It is suitable for roofing sheets, wall panels, and façade cladding when the coating level, paint system, profile design, and installation details are matched to the service condition.